It could appear that you only need to remove the solar panel in the opposite way it was installed, but it’s not as simple as it sounds, however, it’s far more complex than this! If you make a mistake or miss the mark, it can result in breaking plates and could result in a significant amount of cash.
Therefore, a thorough understanding of how to remove the solar panel is important.
However, it’s only suggested when
- You have the appropriate tools.
- You are skilled in electrical equipment (best in relation to solar panels).
- The roof or the area of installation isn’t that difficult to access, but if that’s the case, you should have the right knowledge of SOPs that are based on it.
- Prepared to accept any loss in the event of mishandling of any expensive component.
After you’ve adjusted yourself with the disclaimer Let’s begin the method of removal that is used to remove the solar panels. Because it’s an entire system and all components are connected, removal should be performed cautiously to avoid injury.
Why should you choose a DIY method for Solar Panel Removal?
It would be more efficient to seek out expert help or at the very minimum sought out a basic electrician. Since they’re electrical components and being on a roof requires extra cautiousness. But what if you could save some cost by making the work yourself? Yes, it will cost quite a bit of money to segregate the panels.
Buy the best solar panels in Pakistan from Inspect Energy that has listed the best solar companies in Pakistan and only works with them. We ensure the quality of solar panels as well as solar panel cost in Pakistan.
Method for removing the Solar Panel In a safe and secure manner
The steps for removing the solar panels without harming yourself are as follows:
- Turning off the Power
- Disconnecting the Solar Panels from one another
- Removal of Solar Panels
- Separate Hardware
- Unfastening Cables/Wires
- Destroying the Grounding
- The Components are settled
The Power is Off, and you must shut it off.
It is the first thing to do to stop the current flow in the system for solar energy. Press the disconnect switch or the circuit breakers.
- The system could have two different types of circuit breakers: one on the AC side, and one on the DC side. Be sure to switch them off.
- Then, shut the off switch on your solar converter, which must remain attached to the bank.
What Not To Do It is important to note that the majority of modern solar systems come with a quick shut-off switch that interrupts all current flow connections. They are only used in the event of an emergency like fire or another catastrophe. If you use it for non-installation, it could cause damage to the parts.
Disconnecting the Solar Panels from one another
When the solar energy production has stopped, it is time to disconnect the switch AC power cables and solar systems. While performing the tasks mentioned ensure that you do the following:
- Put on gloves with insulation, as leaks can be noticeable.
- Roof slopes or any other difficult spot for the solar panels should be handled with care, by implementing a plan of action. Wear the harness and take all precautions to remove the plug.
Removal of Solar Panels
Take the solar panels off rooftop mounting devices, and then place them on the ground with care. Standing seam roofs will require more time to install or remove than flat roofs. If the roof slopes it is essential to have at least two more people along with you in order to monitor the procedure.
- Unbolt the panels of the arrays.
- Always remove the solar panel with the panels facing each other. Take one side out first, then tilt another side out.
- In the event that plates appear big, you should call your person who will be putting it to the side that is lower and let it gently be laid down.
- Set the solar plates in an appropriate location or position.
Separate Hardware
Remove the mounting hardware off the roof. Roofs in general are not immune to the solar panel’s weight. Equipment for mounting, which usually is within the permissible limit of your roof is about 2-4 tons per square feet (10-20 kg for square meters).
Unfastening Cables/Wires
Eliminate any electrical cabling or wires off the roof. This will require a lot of care as this section can be very hazardous. Many volts of electricity is generated by the solar panels. Live connections could cause fire or shock due to these circuits. Wear gloves and rubber shoes (if your ground is damp).
Destroying the Grounding System
Remove the grounding connection from the array of panels. When it comes to the removal of the grounding, there are generally two options: one where you can choose to either take the grounding system to the next location or leave it inside the home. If you’re moving to another location, you could leave the grounding in the location you are currently in and increase the value of your home. In other words, taking the rod from the concrete by yourself isn’t a great idea.
Simplify the Components
There might be a need for space for storage of the solar panels on your roof. Set the components in a shaded and dry location. Make sure you add packaging materials or forms between the panels. Most of the time the panels will last well outside, but only in a spot that is shielded from elements of rain and wind. When the panels have been disconnected from the electrical connections on the rear of the panel can be vulnerable to water intrusion. Failure of solar panels can result from moisture and humidity in the connectors.
Prerequisites
- Use a large, thick towel or other transparent cloth to cover each part of the system completely.
- Turn on the voltage meter and set it to directly measuring voltage (DC).
- Unplug the wires that are connected to the solar panel. Remove the screws or nuts then roll them up and put them in a proper place.
Want to check the solar panel battery price in Pakistan Visit Inspect Energy.
